fiatguy85

Hey,
I'm planning on making a table with beer caps embedded in it. I'm thinking the epoxy will be 1/4"-3/8" thick. I was wondering if anyone had any experience making a thick epoxy table top, any advice, and if anyone could recommend an epoxy. I have found a couple online that look promising.

Thanks

clavus

I used a 2 part epoxy specifically designed for bar tops. Heck, it might have even been called "Bar Top. Don't remember.

What is super duper abso-fuckin-lutely CRITICAL is to mix it well. If you don't, you will end up with a soft, sticky spot that will not cure. Then you are FUBAR. I had to throw away the first top I tried for this very reason. Don't be like me.

Make an edge around your perimeter with masking tape, with a fourth of the tape sticking up. The tape will form the walls of the "cup" that you will fill with the epoxy. When it is dry, simply remove the tape. It should come right off, revealing a nice, clean edge.

__________________
Ass, gas or grass. Nobody rides for free.

Rekna

Just remember the second you get married your wife is going to throw it out

fiatguy85

I like to think I've got a little while before I worry about that

Thanks for the advice Clavus!

God of Thunder

Make sure to use in a weeeellllllllll ventilated area. That stuff is powerful.

My other tip is that during the mixing process, air bubbles are created. Once you pour the mixture on the table top you can wave a blow torch over the top of the epoxy to get rid of the bubbles. Just wave it a few inches above the epoxy and watch the bubbles come to the surface.

__________________
I reject your reality, and substitute my own

-- Adam Savage

cj2112

wait...isn't this stuff highly flammable until it cures?

God of Thunder

I never had a problem with the stuff I used. I couldn't begin to tell you the name of the product, it was so many years ago. We used to make plaques for graduation presents. We would put senior pictures on a plaque and then pout the two-part mixture over the top of it. we would then use the blow torch as described above to remove the air bubbles as it was setting up.

__________________
I reject your reality, and substitute my own

-- Adam Savage

fiatguy85

Construction has started. Pictures on Flickr:

cj2112

Very cool...just one problem...isn't "Tec" spelled Tech?

fiatguy85

It's still in progress. Eventually the entire thing will be covered in caps.

cj2112

This is gonna really cool, I love the idea!

clavus

No worries. Use the torch. I did it and I did not erupt into a fire-ball of death. the directions even tell you to do it this way.
-----Added 11/1/2009 at 05 : 09 : 38-----
Holy shit.! !!!!!!!!!!!!!!!!!!!!!!!!!!!!DANGER DANGER DANGER!!!!!!!!!!!!!!!!!!!!!!!!!

Do a small test first. Make sure your bottle caps do not float to the surface due to the air trapped beneath them. You may need to weight them down or glue them in place, or do a thin first pour to hold them where they belong.

__________________
Ass, gas or grass. Nobody rides for free.

thingstodo

I saw a thing about companies that make the plaques. They heat the stuff in an oven at a pretty high temp to get the bubbles out. Sounds like the torch method should work as well since you sure won't find a bar top sized oven! They also mixed in colors which might be interesting to do as a swirl effect in different areas of your top.

__________________
If you're wringing your hands you can't roll up your shirt sleeves.

Stangers have the best candy.

fiatguy85

Mixing in colors is something I hadn't thought about. I know i don't want to do anything too distracting from the designs in the caps. We're currently still figuring out the little details of the design and hopefully will be laying epoxy this week or the next.

biznatch

fiatguy, I want an update dammit.

__________________
Check it out: The Open Source/Freeware/Gratis Software Thread

girldetective

Hey! Could you use a blowdryer instead of a blowtorch for releasing bubbles?

Im interested in this stuff (for use other than a bottle cap table so no competition). What is it and where does one purchase it?

__________________
As far as possible, without surrender, be on good terms with all persons...be cheerful; strive for happiness - Desiderata

fiatguy85

Haha unfortunately we've been burdened with school work and have not finished yet as we had hoped to. We've updated the design to just a big G and T, I'll try to post pictures by the weekend. The frame has now been stained and the back board painted black on one side, still have to do the other.

The epoxy we chose is from USComposites, we will be using 4 gallons by our calculations:

Epoxy :omgKleer Koat Table Top Epoxy

It was basically the cheapest, made specfically for this purpose and I saw at least one similar design using this that seemed to turn out well. Hopefully we'll be finishing up in the beginning of May and I will try to post more pictures soon and as we go.

Rekna

you should mark the beer pong cup spots with bottle caps

fiatguy85

Thanks Rekna, we are actually doing that. We're going to have a different group of caps for each cup marked out It's not evident in the previously posted pictures, but more are coming tomorrow, I promise.

fiatguy85

Ok, sorry it took so long, but here is the updated table design. Photos on Flickr





There is some progress on the frame and base board, but I'll post pictures when we get them finished up. Hopefully in a couple weeks.

fiatguy85

An unfortunate update: the project is currently on hold while I'm moving about and getting a job (just graduated from school). Hopefully I will be finishing up after I get settled back down.