WinXP only booting with XP CD in drive! Maxtor SATA drive - Abit KV7 - Tilted Forum Project Discussion Community

bfoz · 09-22-2003, 08:45 AM

After installing XP my system now will only boot with the XP CD in the drive and CD-ROM set as first boot device. If I selected Hard-Drive as the boot option, it just says "NO BOOT DRIVE DETECTED" or similar.

If the XP CD is in however, it says "Press any key to boot from CD..." which if you ignore then proceeds to boot from the SATA drive!

I have a DVD ROM and a CD-Wrtier both set as primary on the IDE-0 and IDE-1, respectively, and a Maxtor 7200 RPM 80 Gig SATA drive.

I installed the SATA driver (F6 during installation and used the provided floppy from Abit).

I think I've tried all combinations of boot options in BIOS.

I can't be the only one in the world with this problem!

Anyone seen and resolved this?

I have also posted this on the motherboards forum, but think it might be better in this one!

Kaos · 09-22-2003, 07:52 PM

Both your DVD Rom and CD Writer are set as Primary? Does this mean you have your Hard Drive set as a slave?

If so, I suggest you put the Hard Drive on the IDE-0 set as Master, and put the DVD Rom and CD Writer on IDE-1 set as Master and Slave respectively.

Dilbert1234567 · 09-22-2003, 10:05 PM

hmmm chekc with the mother board maker. ther may be a bios update for it.

bfoz · 09-23-2003, 01:06 AM

It's a SATA drive, so it is on a seperate controller.

Also, the only BIOS on the website is the release version that came with the board.

The thing that is confusing me is that it's A-bits flagship Athlon board, with Microsoft's flagship OS and a well known drive manufacturer. I can't believe I am the only one who has seen this problem!

R_one · 09-23-2003, 04:17 AM

Need to set your bios to boot from the sata in the in Bios. It's either going to say "sata" or "SCSI".

Elitegibson · 09-23-2003, 10:00 AM

Quote:

Originally posted by R_one
Need to set your bios to boot from the sata in the in Bios. It's either going to say "sata" or "SCSI".

Ditto

bfoz · 09-23-2003, 12:33 PM

Hiya,

I'll give it a try, but I'm sure I tried all of the settings.

Cheers,

Bfoz

poof · 09-23-2003, 09:28 PM

As said above, set the the boot sequence to SCSI. On my SOYO there is <b>another</b> place just below boot sequence that wants to know which sata to go to first (sata1, sata2,) I use sata3 for a single drive, and sata3, sata4 for my raid.

bfoz · 09-27-2003, 01:48 AM

Right, there isn't a SCSI option. I basically have "Hard Drive", "Floppy", "USB - SCSI", "USB - Floppy" and "CD-ROM". The only one that works is "CD-ROM" when the XP CD is in the drive as before.

Very strange. My old KT7 board had a "ATA100-RAID" option to boot from.

Even though the only BIOS on the A-bit website is the relsase one, it seems to be a slightly higher version than the one I have, I am going to try flashing it so see if that sorts it.

If that doesn't work, I'm stuck!

Cheers,

Bfoz

steveincolumbus · 09-27-2003, 10:13 AM

i thought on abits site it had release 1,1 for the bios
Make sure it is not set to raid and that it is enabled in bios
make sure that the partition is active

poof · 09-27-2003, 11:22 AM

Try usb scsi. Once it see's there is no usb it will go to scsi, I think. Just guessing. I can't hurt to try, I mean, it doesn't work now.

bfoz · 09-30-2003, 03:37 PM

Sorted it!

Thanks guys.

It was the BIOS. Despite BIOS version 1.1 on ABit's site being the "release" version with no bug fixes listed, my board had BIOS version 1.0.

Cheers,

Bfoz

09-22-2003, 08:45 AM	#1 (permalink)
bfoz Upright Location: Manchester, England	WinXP only booting with XP CD in drive! Maxtor SATA drive - Abit KV7 After installing XP my system now will only boot with the XP CD in the drive and CD-ROM set as first boot device. If I selected Hard-Drive as the boot option, it just says "NO BOOT DRIVE DETECTED" or similar. If the XP CD is in however, it says "Press any key to boot from CD..." which if you ignore then proceeds to boot from the SATA drive! I have a DVD ROM and a CD-Wrtier both set as primary on the IDE-0 and IDE-1, respectively, and a Maxtor 7200 RPM 80 Gig SATA drive. I installed the SATA driver (F6 during installation and used the provided floppy from Abit). I think I've tried all combinations of boot options in BIOS. I can't be the only one in the world with this problem! Anyone seen and resolved this? I have also posted this on the motherboards forum, but think it might be better in this one!

09-22-2003, 10:05 PM	#3 (permalink)
Dilbert1234567 Devils Cabana Boy Location: Central Coast CA	hmmm chekc with the mother board maker. ther may be a bios update for it. __________________ Donate Blood! "Love is not finding the perfect person, but learning to see an imperfect person perfectly." -Sam Keen

09-22-2003, 07:52 PM	#2 (permalink)
Kaos Ssssssssss Location: Ontario	Both your DVD Rom and CD Writer are set as Primary? Does this mean you have your Hard Drive set as a slave? If so, I suggest you put the Hard Drive on the IDE-0 set as Master, and put the DVD Rom and CD Writer on IDE-1 set as Master and Slave respectively.

09-23-2003, 01:06 AM	#4 (permalink)
bfoz Upright Location: Manchester, England	It's a SATA drive, so it is on a seperate controller. Also, the only BIOS on the website is the release version that came with the board. The thing that is confusing me is that it's A-bits flagship Athlon board, with Microsoft's flagship OS and a well known drive manufacturer. I can't believe I am the only one who has seen this problem!

09-23-2003, 04:17 AM	#5 (permalink)
R_one Crazy	Need to set your bios to boot from the sata in the in Bios. It's either going to say "sata" or "SCSI".

09-23-2003, 12:33 PM	#7 (permalink)
bfoz Upright Location: Manchester, England	Hiya, I'll give it a try, but I'm sure I tried all of the settings. Cheers, Bfoz

09-23-2003, 09:28 PM	#8 (permalink)
poof Psycho	As said above, set the the boot sequence to SCSI. On my SOYO there is <b>another</b> place just below boot sequence that wants to know which sata to go to first (sata1, sata2,) I use sata3 for a single drive, and sata3, sata4 for my raid.

09-27-2003, 01:48 AM	#9 (permalink)
bfoz Upright Location: Manchester, England	Right, there isn't a SCSI option. I basically have "Hard Drive", "Floppy", "USB - SCSI", "USB - Floppy" and "CD-ROM". The only one that works is "CD-ROM" when the XP CD is in the drive as before. Very strange. My old KT7 board had a "ATA100-RAID" option to boot from. Even though the only BIOS on the A-bit website is the relsase one, it seems to be a slightly higher version than the one I have, I am going to try flashing it so see if that sorts it. If that doesn't work, I'm stuck! Cheers, Bfoz

09-27-2003, 10:13 AM	#10 (permalink)
steveincolumbus Psycho Location: BFE, Kentucky	i thought on abits site it had release 1,1 for the bios Make sure it is not set to raid and that it is enabled in bios make sure that the partition is active

09-27-2003, 11:22 AM	#11 (permalink)
poof Psycho	Try usb scsi. Once it see's there is no usb it will go to scsi, I think. Just guessing. I can't hurt to try, I mean, it doesn't work now.

09-30-2003, 03:37 PM	#12 (permalink)
bfoz Upright Location: Manchester, England	Sorted it! Thanks guys. It was the BIOS. Despite BIOS version 1.1 on ABit's site being the "release" version with no bug fixes listed, my board had BIOS version 1.0. Cheers, Bfoz