CD-RW Drive Help - Tilted Forum Project Discussion Community

The_Dude · 09-14-2003, 07:27 PM

The tech support has pretty much failed me, so I'm turning to the tfp.

here goes:

I have a pacific digital mach52 (52x24x52) internal ide drive.

it's set to master.

it used to work real well, but now it doesnt like to work at all (read or write).

I get errors and failure when i try to burn cd's and it's EXTREMELY slow when trying to read 'em.

The tech support suggest that I install an "aspi" and then install the firmware for the drive.

I did both, and am still where I started.

It's not a buffer under run because I have a pretty fast pc that can send the data.

I'm linking to a log file from nero that was created during the burn.

Link This is when I was burning a cd (audio) for a friend of mine.

Any suggestions/answers welcome.

Sion · 09-14-2003, 07:58 PM

Dude, if you are trying to write cd's at 52x, be sure the cds you are using are 52x compatable. Other than that, I cant make heads or tails of that log file. IMO, if the drive is having trouble both reading AND writing cds, it should be replaced. still under warranty, right? send it back for a replacement.

meff · 09-14-2003, 08:09 PM

The drive will automatically if the CD supports the speed and will reset the record speed to the max the disk can go..

The_Dude · 09-14-2003, 08:32 PM

Quote:

Originally posted by meff
The drive will automatically if the CD supports the speed and will reset the record speed to the max the disk can go..

yes, it does that (and usually does it to 48x).

the thing that stumps me is the fact that it worked fine a couple of months ago and now it's just acting up.

i'm pretty sure it's under warranty so i might be able to get it replaced. (but I'm off in the dorms and I have no idea where the receipt would be at).

I kept tinkering at it till I found out that it CAN burn at 8x speed.

When I try higher speeds, it never seem to get past the "writing lead-in" part.

I know that my pc can support speeds a lot higher than 8x.

09-14-2003, 07:27 PM	#1 (permalink)
The_Dude The GrandDaddy of them all! Location: Austin, TX	CD-RW Drive Help The tech support has pretty much failed me, so I'm turning to the tfp. here goes: I have a pacific digital mach52 (52x24x52) internal ide drive. it's set to master. it used to work real well, but now it doesnt like to work at all (read or write). I get errors and failure when i try to burn cd's and it's EXTREMELY slow when trying to read 'em. The tech support suggest that I install an "aspi" and then install the firmware for the drive. I did both, and am still where I started. It's not a buffer under run because I have a pretty fast pc that can send the data. I'm linking to a log file from nero that was created during the burn. Link This is when I was burning a cd (audio) for a friend of mine. Any suggestions/answers welcome. __________________ "Luck is what happens when preparation meets opportunity." - Darrel K Royal

09-14-2003, 07:58 PM	#2 (permalink)
Sion Dumb all over...a little ugly on the side Location: In the room where the giant fire puffer works, and the torture never stops.	Dude, if you are trying to write cd's at 52x, be sure the cds you are using are 52x compatable. Other than that, I cant make heads or tails of that log file. IMO, if the drive is having trouble both reading AND writing cds, it should be replaced. still under warranty, right? send it back for a replacement. __________________ He's the best, of course, of all the worst. Some wrong been done, he done it first. -fz I jus' want ta thank you...falettinme...be mice elf...agin...

09-14-2003, 08:09 PM	#3 (permalink)
meff Vanishing, like I do.. Location: Austin, TX	The drive will automatically if the CD supports the speed and will reset the record speed to the max the disk can go.. __________________ Toy-like people make me boy-like.