Tilted Forum Project Discussion Community  

Go Back   Tilted Forum Project Discussion Community > The Academy > Tilted Knowledge and How-To


 
 
LinkBack Thread Tools
Old 04-27-2004, 02:40 PM   #1 (permalink)
Addict
 
working with acrylics

how do you make things with acrylics, like attactch sheets of acrylic plastic, cut acrylic, drill, buy, what tools does one need
noahfor is offline  
Old 04-28-2004, 08:13 AM   #2 (permalink)
Insane
 
Location: Long Island
hope this helps:

Masking
When working with the material, leave the paper masking film on the sheet as long as possible. Except for intricate detail work you should remove the masking only when your project is completed.
Working with acrylic sheet
DO
Keep masking on as long as possible.
Use metal cutting saw blades and drills which are ground for acrylic sheet.
Make sure all tools are sharp.
Use water or drilling oil as a coolant when cutting sheets over 1/8" thick or drilling sheets over 3/16" thick.
Wet the material before cleaning.
DON'T
Use saw blades with side-set teeth. Saw teeth ideally should be ground with 0 degrees of rake and be of uniform height and shape.
Cutting Acrylic Sheet
Cutting with a knife or scriber
Acrylic sheet up to 3/16" thick may be cut by a method similar to that used to cut glass. Use a scribing knife, a metal scriber, an awl, or a utility knife to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16" sheet) along a straight edge held firmly in place. Then clamp the sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Apply a sharp downward pressure to break the sheet along the scribe line. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.
Cutting with power saws
Special blades are available to cut acrylic. Otherwise use blades designed to cut aluminum or copper. Teeth should be fine, of the same height, evenly spaced, with little or no set.
Table and circular saws
Use hollow ground high speed blades with no set and at least 5 teeth per inch. Carbide tipped blades with a triple chip tooth will give the smoothest cuts. Set the blade height about 1/8" above the height of the material. This will reduce edge chipping.
When using a hand held circular saw, clamp the sheet to the work surface and use a length of 1x3 wood to distribute the clamping pressure and act as a guide for the saw.

Feed the work slowly and smoothly. Lubricate the blade with soap or beeswax to minimize gumming from the masking adhesive. Be sure the saw is up to full speed before beginning the cut. Water cooling the blade is suggested for thicknesses over 1/4", especially if edge cementing will be performed.


Saber saws
Use metal or plastic cutting blades. The blades you use to cut acrylic should never be used for any other material. Cut at high speed and be sure the saw is at full speed before beginning the cut.
Hand saws
Good results are possible, but very difficult. Be sure the acrylic is clamped to prevent flexing. Flexing at the cut may cause cracking.
Routers and shapers
Use single fluted bits for inside circle routing and double fluted bits for edge routing. At the high speeds at which routers operate it is critical to avoid all vibration. Even small vibrations can cause crazing and fractures during routing.
Drilling
For best results, use drill bits designed specifically for acrylic.
Regular twist drills can be used, but need modification to keep the blade from grabbing and fracturing the plastic. Modify the bit by grinding small flats onto both cutting edges, so the bit cuts with a scraping action. If the drill is correctly sharpened and operated at the correct speed, two continuous spiral ribbons will emerge from the hole.

Finishing Acrylic
Scraping
The first step in getting a finished edge is scraping. The back of a hacksaw blade is perfect for scraping. Simply draw the corner of the square edge of the blade along the edge of the acrylic.
Filing
A 10 to 12 inch smooth cut file is recommended for filing edges and removing tool marks. File only in one direction. Keep the teeth flat on the surface, but let the file slide at an angle to avoid putting grooves in the work.
Sanding
If necessary, start with 120 grit sandpaper, used dry. Then switch to a 220 grit paper, dry. Finish with a 400 grit wet/dry paper, used wet. Grits as fine as 600 may be used. Always use a wooden or rubber sanding block.
When removing scratches be sure to sand an area larger than the scratch. Sand with a circular motion, and use a light touch and plenty of water with wet/dry papers.

Almost any commercial power sander can be used with acrylic. Use light pressure and slower speeds.


Polishing
Final polishing will give acrylic a high luster. Power-driven buffing tools are recommended without exception. Buffing wheels are available as attachments for electric drills.
A good buffing wheel for acrylic consists of layers of 3/16" carbonized felt, or layers of unbleached muslin laid together to form a wheel. Solidly stitched wheels should be avoided.

The wheel should reach a surface speed of at least 1200 feet per minute. Speeds of up to 4000 feet per minute are useful for acrylic.

Acrylic should be polished using a commercial buffing compound of the type used for silver or brass, or you can use a non- silicone car polish that has no cleaning solvents in it.

First, however, tallow should be applied to the wheel as a base for the buffing compound. Just touch the tallow stick to the spinning wheel, and then quickly apply the buffing compound.

To polish, move the piece back and forth across the buffing wheel. Be careful not to apply too much pressure. Keep the work constantly moving to prevent heat buildup.

Never begin polishing at the edge of the sheet. The wheel could easily catch the top edge and throw the piece across the room or at you.


Forming Acrylic
Acrylic can be heated to make it pliable. It will become rigid again when it cools. Never heat acrylic in a kitchen oven. Explosive fumes can accumulate inside the oven, and ignite.
A strip heater is the best tool to form acrylic. This tool will only form straight line bends. Buy one from your acrylic dealer. The strip heater will heat just the area to be formed.

Heat the sheet until it begins to sag at the bend line. The bend should be made away from the side exposed to the heating element. Sheet thicker than 3/16" should be heated on both sides for a proper bend. Use forming jigs or clamps for best results, and wear heavy cotton gloves when handling heated acrylic.

Forming other than straight line bends will generally require specialized equipment and jigs.


Joining Acrylic
Solvent cement is recommended for joining acrylic. There are two techniques for solvent cementing, capillary and dip or soak methods.
Capillary cementing
This is the most popular method for joining acrylic. However, this method will not work at all unless the parts to be joined fit together PERFECTLY.
Make sure the parts fit properly. Then join them with masking tape or clamp them in a form to hold them firmly in place. It is important that the joint be in a horizontal plane, or the cement will run out of the joint.

Apply the cement carefully along the entire joint. Apply from the inside of a box-corner joint, and on both sides of a flat joint. A needle-nosed applicator bottle is recommended. The thin cement will flow into the joint through capillary action and form a strong bond. Maximum bond strength will not be reached for 24 to 48 hours.


Soak or dip cementing
This sounded like a real pain in the butt, and is suggested only for thick joints.
Viscous cementing
Viscous cements are used for joints that can't be cemented with capillary or soak cementing, either because the joint is difficult to reach or because the parts don't fit properly. Viscous cement is thick and will fill small gaps. It can make strong transparent joints where solvent can't.
You can make your own viscous cement by dissolving chips of clear acrylic sheet in a small amount of solvent.

Apply a small bead of cement to one side of the joint, join the pieces, and tape or clamp in place until cured.
__________________
"A friend with weed is a friend indeed"
agball is offline  
Old 04-28-2004, 10:57 PM   #3 (permalink)
Junkie
 
fhqwhgads's Avatar
 
I think cooling is important when cutting acrylic. I was making a jig on my scrollsaw the other day, cutting a piece of 1/4" acrylic. The blade is so fine and got so hot that the area where I cut melted back together as I went along. When I got to the end of the cut, the piece was still stuck together.

I put the piece on my tablesaw instead, and it made a hell of a mess with all the plastic shavings. Wish I had a bandsaw...
fhqwhgads is offline  
Old 04-29-2004, 05:31 PM   #4 (permalink)
Poo-tee-weet?
 
JStrider's Avatar
 
Location: The Woodlands, TX
ive cut it with a dremel cutting blade... hard to do well...
__________________
-=JStrider=-

~Clatto Verata Nicto
JStrider is offline  
Old 04-30-2004, 05:27 PM   #5 (permalink)
Buffering.........
 
merkerguitars's Avatar
 
Location: Wisconsin...
Talk to bodypainter he's a master at working with that stuff
__________________
Donate now! Ask me How!

Please use the search function it is your friend.

Look at my mustang please feel free to comment!

http://www.tfproject.org/tfp/showthread.php?t=26985
merkerguitars is offline  
Old 05-02-2004, 05:23 PM   #6 (permalink)
Crazy
 
Use a jigsaw with a medium toothed blade at a slow speed. Just kinda bump the trigger to get a feel for it. You want to cut out enough material so that you can move through it quickly without melting. The stores usually have scraps that you could get to practice on for free. If you don't have a table saw, and need to make a long cut, there's a tool that you use to scribe the acrylic with, making a few cuts and then popping it all at once. Just takes some practice.
soopadoopa is offline  
Old 05-06-2004, 06:05 PM   #7 (permalink)
Addict
 
the first post was very good. With his exceptions noted, acrylic can be worked in a somewhat similar fashion to wood - being careful for cracking and stress and the right blades and bits, etc. I glue with thickened solvent cement. I get most of my materials and glues, etc here:

http://shop.store.yahoo.com/ecomplastics/index.html
jbrooks544 is offline  
Old 05-06-2004, 06:17 PM   #8 (permalink)
Poo-tee-weet?
 
JStrider's Avatar
 
Location: The Woodlands, TX
my room mate is trying to give plexi a frosted/ sandblasted look...

he wants to make a sakura blossom looking etching, then put leds in the edge of the plexi so the blossoms light up...

weve messed with my dremel... but havnt had that great of results...anyone have any ideas?
__________________
-=JStrider=-

~Clatto Verata Nicto
JStrider is offline  
Old 05-30-2004, 09:36 PM   #9 (permalink)
Crazy
 
Location: upstate, NY
try the engraving tool for your dremel, and kind of color in the frosted area to be lit up.
i've used this technique before and it works pretty well, I'd obviously try it out on some scrap pieces first.
limited is offline  
Old 05-31-2004, 12:14 AM   #10 (permalink)
Loser
 
Quote:
Originally posted by JStrider
my room mate is trying to give plexi a frosted/ sandblasted look...

he wants to make a sakura blossom looking etching, then put leds in the edge of the plexi so the blossoms light up...

weve messed with my dremel... but havnt had that great of results...anyone have any ideas?
You may want to try a window etching kit, or even the spray type window frosting. With practice, it can be done with coarse sandpaper.
WarWagon is offline  
 

Tags
acrylics, working

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 01:47 AM.

Tilted Forum Project

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
© 2002-2012 Tilted Forum Project

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360