Tilted Forum Project Discussion Community  

Go Back   Tilted Forum Project Discussion Community > The Academy > Tilted Knowledge and How-To

Notices

 
 
LinkBack Thread Tools
Old 02-12-2004, 01:50 PM   #1 (permalink)
Gentlemen Farmer
 
j8ear's Avatar
 
Location: Middle of nowhere, Jersey
remove custom lettering from door of pickup

I have tried a hair dryer and a razor blade. Works but seems very time consuming and scratches the paint quite a bit.

Maybe I'm not getting things hot enough, but I did lay into it.

I have also tried a wire wheel on my grinder, I figured if I was gonna scratch it anyway, I might as well do it quickly.

This resulted in mushy melted and smeared vinyl lettering everywhere.

No longer readable, but definately visible.

Anywho...I figured someone knew a reasonable way to remove the name of the previous owners business from my new to me pickup truck. A spray of some sort that will degrade or dissolve the adhesive, perhaps?

I am pretty sure it is just white vinyl lettering on blue paint.

Anyone have experience with decaling or pinstriping?

Any tips appreciated.

Gracias,

-bear
__________________
It's alot easier to ask for forgiveness then it is to ask for permission.
j8ear is offline  
Old 02-12-2004, 04:17 PM   #2 (permalink)
Crazy
 
Location: louisianna
if you're not concerned about the finish,paint a sander will work ,of corse it will have to be primed and painted after. i would call a body shop or somewhere that applies the stickers or decals to see if they have any advise,on it .some paint thinner or gas or somesort of glue remover might help as well. good luck and let us know how it goes.
mazak is offline  
Old 02-12-2004, 05:27 PM   #3 (permalink)
Crazy
 
Try some WD-40 with the razor blade. I've had that work very well before. Spray some on, let it sit, then carefully scrape. When it gets tough to scrape, spray again and repeat. Good luck.
soopadoopa is offline  
Old 02-12-2004, 07:09 PM   #4 (permalink)
MSD
The sky calls to us ...
 
MSD's Avatar
 
Super Moderator
Location: CT
3M makes a buffing wheel that will remove pinstripes. Use that in a low-speed drill (no dremel or grinder) and it'll take off teh lettering and not the paint. Don't touch it with metal. You also can try a heat gun, as long as it's not painful to touch (might be uncomfortable,) you can save the paint.
MSD is offline  
Old 02-12-2004, 07:19 PM   #5 (permalink)
Gentlemen Farmer
 
j8ear's Avatar
 
Location: Middle of nowhere, Jersey
I'm not all that concerned about the paint honestly...

But I definately should have known that 3M made something appropriate. Those Minnesota Miners and Manufacturers make everything...and everything they make is excellent.

I'll see what my supply house house has.

Thanks men.

-bear
__________________
It's alot easier to ask for forgiveness then it is to ask for permission.
j8ear is offline  
Old 02-12-2004, 09:59 PM   #6 (permalink)
Insane
 
Location: On a gravel road rough enought to knock fillings out of teeth.
Lacquer thinner does wonders on adhesives. And it will also tell you the exact location of any small cuts on your hands.
__________________
Judge me all you want, but keep the verdict to yourself.
BoomTruck is offline  
Old 02-13-2004, 01:38 PM   #7 (permalink)
!?!No hay pantalones!?!
 
saltfish's Avatar
 
Location: Indian-no-place
I used mineral spirits and a hair dryer.

Worked really well, keep a rag soaked in mineral spirits in one hand and slowly pull backard on the vinyl sticker with the other, as the sticker peels, rub the newly exposed area to soften the adhesive.

-SF
saltfish is offline  
Old 03-10-2004, 07:47 AM   #8 (permalink)
Gentlemen Farmer
 
j8ear's Avatar
 
Location: Middle of nowhere, Jersey
Turns out I just needed the weather to warm up, the patient touch of my long fingernailed wife, and a little elbow grease

Lettering gone. No chemicals, tools, or abrasives.

Thanks Again,

-bear
__________________
It's alot easier to ask for forgiveness then it is to ask for permission.
j8ear is offline  
Old 03-10-2004, 10:31 AM   #9 (permalink)
Transfer Agent
 
troit's Avatar
 
Location: NYC
Here's one tip not listed -- use brake fluid. Works like a charm and won't hurt the paint.
__________________
I've yet to dephile myself...
troit is offline  
Old 03-10-2004, 05:53 PM   #10 (permalink)
:::OshnSoul:::
Guest
 
Goof Off. buy it and you WILL be happy.
 
Old 03-10-2004, 06:16 PM   #11 (permalink)
Addict
 
I manage a fleet of vans and have to do this every time I sell an old one.

Usually a heat gun and straight razor works. Not a blow drier but a real heat gun - they're cheap.

If no go with that route - older and drier, brittle stuff:
Use 3M "woodgrain and stripe remover"
http://products3.3m.com/catalog/us/e...er/output_html
Spray only on small area at a time, let it work and scrape off.

Then use the adhesive remover if you have sticky stuff left over:
http://products3.3m.com/catalog/us/e...eme_us_aad_3_0

Other products are here too:
http://products3.3m.com/catalog/us/e...er/output_html

I have found that most auto parts stores have one or two cans of each of these or can get them in a day or two.
jbrooks544 is offline  
Old 03-14-2004, 12:31 AM   #12 (permalink)
Insane
 
Quote:
Originally posted by troit
Here's one tip not listed -- use brake fluid. Works like a charm and won't hurt the paint.
Brake fluid will melt the fucking paint right off of his car, buddy.
TopRamen66 is offline  
Old 03-27-2004, 03:00 AM   #13 (permalink)
Junkie
 
james t kirk's Avatar
 
Location: Toronto
Quote:
Originally posted by TopRamen66
Brake fluid will melt the fucking paint right off of his car, buddy.
OH YEAH.

Brake fluid is the world's best paint stripper.
james t kirk is offline  
 

Tags
custom, door, lettering, pickup, remove


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 02:05 PM.

Tilted Forum Project

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
© 2002-2012 Tilted Forum Project

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360