Airbrush problem - no air pressure - Tilted Forum Project Discussion Community

todd · 08-16-2004, 09:29 PM

I pulled out my Badger Anthem 155 after it had been sitting in a shoebox for about 2 months to find that I get no air when I push the trigger.

The problem is something in the gun. I know this because I can unhook the hose from the gun and open the Propel can and plenty of air comes out. It's just when I hook it up to the gun that nothing gets through. It's only been used a few times, and I always cleaned it well with paint thinner and water after each use. If there was paint clogged I wouldn't think that would restrict the air flow though, would it?. The trigger springs up and down nicely, so the trigger isn't jammed.

The manual says nothing about this problem.
Anybody have any idea what might be wrong? I have a few things I need to paint and i'd love to be able to use this.

Thanks

clavus · 08-16-2004, 09:32 PM

Does the needle move when you pull the trigger, or is it stuck in place?

todd · 08-16-2004, 09:57 PM

Yea it moves with the trigger.

I also removed the needle completely once and put it back in, thinking maybe something wasn't hooking up properly. Didn't change anything though.

MoNoXiDe_XXX · 08-17-2004, 02:36 PM

Probly clogged with something on the ait intake on the gun

todd · 08-17-2004, 03:46 PM

I just dismantled the whole valve and blew through any holes. Nothing appeared to be obviously blocked. I don't really know what it's supposed to look like though. I reassembled it and it still does the same thing.

todd · 08-22-2004, 08:40 AM

It still isn't working. The problem seems to be with the valve though. I took the whole valve off, and can press on the 'valve trigger' (the thing the real trigger presses to open the valve) and nothing happens. Sometimes a little bit of air comes out, but never very much. Do you think its something with the washer seal in there? Maybe it isn't moving with the trigger. I'll try lubing it a bit...

giantpizzaman · 09-05-2004, 09:00 PM

any progress? i dont know what i can tell you as of now, if youve tryed all those things..

08-16-2004, 09:29 PM	#1 (permalink)
todd Addict Location: Chicago	Airbrush problem - no air pressure I pulled out my Badger Anthem 155 after it had been sitting in a shoebox for about 2 months to find that I get no air when I push the trigger. The problem is something in the gun. I know this because I can unhook the hose from the gun and open the Propel can and plenty of air comes out. It's just when I hook it up to the gun that nothing gets through. It's only been used a few times, and I always cleaned it well with paint thinner and water after each use. If there was paint clogged I wouldn't think that would restrict the air flow though, would it?. The trigger springs up and down nicely, so the trigger isn't jammed. The manual says nothing about this problem. Anybody have any idea what might be wrong? I have a few things I need to paint and i'd love to be able to use this. Thanks

08-16-2004, 09:32 PM	#2 (permalink)
clavus pow! Location: NorCal	Does the needle move when you pull the trigger, or is it stuck in place? __________________ Ass, gas or grass. Nobody rides for free.

08-17-2004, 02:36 PM	#4 (permalink)
MoNoXiDe_XXX Psycho Location: Thunder Bay	Probly clogged with something on the ait intake on the gun __________________ ------------------------ I may be ugly, But at least I aint got no money!

09-05-2004, 09:00 PM	#7 (permalink)
giantpizzaman Upright Location: EH?	any progress? i dont know what i can tell you as of now, if youve tryed all those things.. __________________ hang out with your wang out then rock up with your cock up

08-16-2004, 09:57 PM	#3 (permalink)
todd Addict Location: Chicago	Yea it moves with the trigger. I also removed the needle completely once and put it back in, thinking maybe something wasn't hooking up properly. Didn't change anything though.

08-17-2004, 03:46 PM	#5 (permalink)
todd Addict Location: Chicago	I just dismantled the whole valve and blew through any holes. Nothing appeared to be obviously blocked. I don't really know what it's supposed to look like though. I reassembled it and it still does the same thing.

08-22-2004, 08:40 AM	#6 (permalink)
todd Addict Location: Chicago	It still isn't working. The problem seems to be with the valve though. I took the whole valve off, and can press on the 'valve trigger' (the thing the real trigger presses to open the valve) and nothing happens. Sometimes a little bit of air comes out, but never very much. Do you think its something with the washer seal in there? Maybe it isn't moving with the trigger. I'll try lubing it a bit...