Tilted Forum Project Discussion Community

Tilted Forum Project Discussion Community (https://thetfp.com/tfp/)
-   Tilted Knowledge and How-To (https://thetfp.com/tfp/tilted-knowledge-how/)
-   -   How to drill through glass? (https://thetfp.com/tfp/tilted-knowledge-how/40849-how-drill-through-glass.html)

01-08-2004 12:19 AM

How to drill through glass?
 
Does anyone know how to drill through glass?

I searched on google and this is what I got.

To Drill through glass you will need the following materials:

Piece of steel wire.

File

First: File the wire to the shape of the Drill. The wire must be tempered in the following way:

1. Heat End of Wire-Drill on an open flame until it is a faded or dull red color.

2. After heated Place in Metallic Mercury. (caution This is a Hazardous substance)

The wire drill in this manner will bore through glass very easy.

To lubricate the drill (always do this when drilling Glass) Use oil of turpentine with a small amount of camphor.

3. Start to drill. Careful not go drill the entire way through one side of the glass because you will cause the glass to break if you do so.

4. Drill part of the way through, almost all the way. Then finish my drilling from the opposite side of the glass.

If you are unable to do this then, as when you are drilling through items such as bottles, place in water or fill with water.

WORD TO THE WISE: When you create your drill, do not make the edges to sharp also do not make the cutting edge to acute. This will cause the Drill to cut a little slower but you will end up with a cleaner result, with less breakage and less holes.

Does anyone know what kind of wire they are talking about? and where could you get mercury? I see these directions on a lot of websites so I think it works but Im confused on what they are talking about.

Locobot 01-08-2004 02:53 AM

I'll only help you if you can garantee me that this is for bong-construction purposes.

dailyjo2003 01-08-2004 08:09 AM

Take it to place that sells and cuts glass

Scorpion23 01-08-2004 10:01 AM

By the way they're talking, it's almost like you take a steel rod and file it into the shape of a drill bit. The only handy sources of mercury that I know of are old thermometers and tilt switches. But you have to be careful since the mercury may vaporize slightly when you stick the red-hot wire in it.

I used to know a guy that drilled holes in bottles to use as incense burners. He used diamond-tippd drill bits on a drill press so the angle would stay constant. It gave nice clean holes, just go slow and it should work out fine.

Mister B 01-08-2004 03:20 PM

If you are scared about the glass breaking or shattering while drilling, wrap tape around the glass.

Lebell 01-08-2004 04:38 PM

Umm, just use a diamond tipped glass drill bit and take it slow and easy.

For small holes, use in a Dremel mototool.

For larger ones, I would probably use a drill press or take it to a shop. They'll probably charge you a couple of bucks max.

01-08-2004 05:31 PM

Thanks for all the feedback. Im def. am gonna go to home depot to look for a bit. Thanks for all the tips also.

noblejr 01-08-2004 09:30 PM

I used to make lamps out of coke bottles. I would use a dremel-like tool with a "burr" drill bit (a small rounded bit, like a dentist would use). If I drilled too much at once, the bottle would heat up too quickly and crack, so I just took my time and once I had drilled through I used a polishing stone bit to smooth out the edges of the hole.

GuttersnipeXL 01-11-2004 12:51 PM

Quote:

Originally posted by Locobot
I'll only help you if you can garantee me that this is for bong-construction purposes.
As soon as I read the title of the thread...I knew it was for bong related purposes. I'd be quite suprised if it wasn't!

zer010gic 01-12-2004 08:05 AM

Use a diamond tipped bit and some wd-40 to cool the spot you are drilling and you sould be fine. I have accually dont this before and thats the method I used.

mtsgsd 01-13-2004 07:05 AM

by a glass drill bit in any hardware store. Odd looking spear point shaped drill. Keep the speed down as spec.'d in the instructions. Much simpler. :)

theguyondacouch 01-17-2004 10:25 AM

I use a dremel at VERY low speeds with a diamond tip bit. it normally used for engraving, but it works good for slow removal of glass. Just be sure to run it at like 1500 rpm MAX!!!

moonstrucksoul 01-17-2004 04:38 PM

oooooh now i can make my SoBe bong, thanks
http://www.majickq.com/sobe465logo.jpg

theguyondacouch 01-17-2004 06:23 PM

HAH! im not the only one with a sobe bong then!

floydthebarber 01-24-2004 01:30 AM

As above ....use a dremel.

krwlz 01-24-2004 05:39 PM

Well, we used the glass drilling bit the other day. Worked great. About 7 bucks for a 3/8" bit I think.

Finished off with the dremel.

clavus 01-25-2004 01:05 PM

Drill it under running tap water to keep things cool.

lrsurfer 01-27-2004 02:41 PM

Make sure you put a paper tape over the glass before you drill, it will prevent drill from slipping

clavus 01-27-2004 04:52 PM

Not that I'd know anythign about this, but if you have a metal stem for your bond, you are going to want an oval hole. The stem is going to go in at an angle, not perpendicular to the side of the bottle. So drill a hole, then use a Dremmel to grind it to the right shape...OR - drill a hole that is much to big, and use silicone to fill the gaps.

Also, it's best to use a grommet, so you can slide the stem out later if need be.

LStanley 01-27-2004 07:23 PM

Quote:

Originally posted by clavus
Not that I'd know anythign about this, but if you have a metal stem for your bond, you are going to want an oval hole. The stem is going to go in at an angle, not perpendicular to the side of the bottle. So drill a hole, then use a Dremmel to grind it to the right shape...OR - drill a hole that is much to big, and use silicone to fill the gaps.

Also, it's best to use a grommet, so you can slide the stem out later if need be.

lol you crack me up :p

EruptiveDreamz 01-28-2004 02:58 PM

I don't know .. but a friend of mine shared with me that he bought a bit for his dremel to drill thru glass with and he drilled holes into yes bad bad light bulb and didn't think he accomplished anything. Till after he put the lightbulb aside and noticed all these lil pieces of glass he had drill in the tips of his fingers. Embedded! Obviously the bit worked and he got what was justified because of the reasoning he was drilling the holes.

nate_dawg 02-02-2004 06:33 PM

Quote:

Originally posted by clavus
Not that I'd know anythign about this, but if you have a metal stem for your bond, you are going to want an oval hole. The stem is going to go in at an angle, not perpendicular to the side of the bottle. So drill a hole, then use a Dremmel to grind it to the right shape...OR - drill a hole that is much to big, and use silicone to fill the gaps.

Also, it's best to use a grommet, so you can slide the stem out later if need be.

sheesh, how about a glass slide?
no need to drill another hole for the carb then

plus you dont get that icky metallicky taste. if you're making a glass bong, might as well do it right and go all glass.

MSD 08-19-2004 08:19 PM

Quote:

Originally Posted by EruptiveDreamz
I don't know .. but a friend of mine shared with me that he bought a bit for his dremel to drill thru glass with and he drilled holes into yes bad bad light bulb and didn't think he accomplished anything. Till after he put the lightbulb aside and noticed all these lil pieces of glass he had drill in the tips of his fingers. Embedded! Obviously the bit worked and he got what was justified because of the reasoning he was drilling the holes.

So the light bulb bomb isn't just a myth?

tropple 08-20-2004 03:28 PM

Oh,, absolutely not. But it's usually much more efficient to go in from the bottom. It used to be that you could heat and remove the base of the bulb. I don't know if it's still possible. It's been a long time.

kazoo 08-20-2004 08:00 PM

This has to be bong-related. I've read this same inquiry a half-dozen times since joining the board. HELLO??? :crazy: The least you guys can do is bring Doritos. :thumbsup:

BHabarow 08-26-2004 02:43 AM

Seems you've already got the answers you wanted, but when it comes to drilling holes in glass bottles, you can fill the bottle with sand and use a regular drill bit. Works for certain. I'm assuming the sand stops the vibration in the glass (cause of breakage) when cutting? Anyway. Good luck with whatever you were doing.. oh yes, the bong. Hazah!

Sp0rAdiC 03-12-2006 06:32 PM

I know this is a really old thread, but I figured this question fit. I have a glass slide for my bong, and I really want to add a carb to the slide because it has a chamber that fills up with smoke and then... just sits there. I want to be able to clear the chamber and then remove the slide. So what I'm asking is: Is the procedure for cutting blown glass any different than cutting bottles?


All times are GMT -8. The time now is 11:36 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
© 2002-2012 Tilted Forum Project


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47