My Project 84 Mustang GT - Page 4 - Tilted Forum Project Discussion Community

Scorps · 03-27-2004, 12:34 PM

Quote:

Originally posted by merkerguitars
Well I got some pulleys off of ebay for $56 they are blue and made of steel but they are underdrive ones...they will get me buy until i get those made by my friend...i have a bunch more stuff to be sent off to be powered coated. i can pick up my block on tuesday then i should have plenty more pics

Underdrive pulleys? never heard of those before.

merkerguitars · 03-28-2004, 09:35 PM

Underdrive pulleys reduce how much your alternator, water pump and power steering turn so you free up more horsepower....less work they do = more hp

Scorps · 03-29-2004, 08:50 AM

Quote:

Originally posted by merkerguitars
Underdrive pulleys reduce how much your alternator, water pump and power steering turn so you free up more horsepower....less work they do = more hp

OH...but that means less power from alternator...right?

merkerguitars · 03-29-2004, 10:52 AM

Yup less power from the alternator but I have to buy a bigger alternator cause mine is a 55 amp from the factory and there is no way it will power my electric fan, electric fuel pump, and a small decent stereo system all at once....

This is what I need to buy yet to get it finished
Motor mounts and transmission mounts
electric fuel pump
fuel filter
MSD 6al ignition box
2 gauge cable to move my battery to the trunk
hi torque starter
105 amp alternator
Battery box
Thermostat housing
Thermostatic switch to turn my electric fan on and off automatically
Relays for rewiring my power under the hood
Electric Fan
Roller Rocker arms
New Head bolts
Hose Clamps
Radiator clmap
lower radiator hose
water pump to intake manifold hose
synthetic atf
spark plug wires
power steering pump
u joint
4 gauge wire
fuel pump block off plate
cable ties
lots of oil 20qts+
oil filter
oil pressure sensor
clutch
steel input bearing retainer for my tranny
tranmission seals (might as well replace them why the tranny is out)
serpentine belt
ignition coil

Scorps · 03-30-2004, 08:49 AM

WOW!

that is going to burn I nice hole in your pocket....must be nice to have that kinda money.....I hoping I can afford the get a loan soon!

merkerguitars · 03-31-2004, 06:12 AM

Ok I just ordered a bunch of stuff, roller rockers, carb studs, arp head bolts, fuel pump blockoff plate, chrome thermostat housing.
I picked up my block, wow it's beautiful, some bastard put a 3.8 taurus engine on the stand that my friend loaned me so i'm gonna have to take the engine and chuck it outside. Hopefully this weekend I can get the engine on the stand, then I can start assembling.

merkerguitars · 04-05-2004, 11:27 PM

Well I got my block on the stand and painted, I'll have to post pics of it. It took me about 1/2 hour to mask everything off but I had very very little overspray. I decided not to assemble till I have all my parts ready so I can assemble it in a day. I started to clean up the wiring in the engine compartment.....not to bad....I have alot of stuff I need to get rid of. Some of the stuff has been cut and spliced before....but shouldn't take me too long to clean up. I just have to double check what some of the wires are before cutting them. Then I can steam blast and paint it

Scorps · 04-06-2004, 08:19 AM

Damn this is the fun part....I love putting engines back together!

merkerguitars · 04-08-2004, 01:39 PM

w00t got some parts today my forged aluminum roller rockers came and my chrome thermostat housing

also I bought a set of mechanical gauges

Update April 12th

I have to call the machine shop today and see if my heads are done.

No pics until next week. I loaned my camera to my roomate that will be on vacation for a week.

I started snipping wires....and I fucked up big time and lost my lights

turns out the ammeter wire is tied in with the head lights...but it's easily fixable. I bought a dealer wiring manual on ebay. All my manuals have shitty wiring diagrams and some of the diagrams are the wrong color codes. Hopefully next week i'll start to make my custom gauge holder. I want to put quick disconnects on the headlight wiring so I can pull the harness back and steam blast all the paint off of all the sheet metal in my engine compartment. I was looking at my rubber fuel lines. One has some nice scarring on it. Thankfully I never drove the car. I'm gonna replace all the rubber lines.

merkerguitars · 04-14-2004, 09:26 PM

Ok now i decided to buy a windage tray. I am pretty much buying one cause my dad highly recommended it. Hopefully after I rack in some more money next week I'll be able to buy my MSD 6AL box and a nice Optima red top battery. And luckily in a few weekends I can assemble my engine. Next week i'm gonna pull my car into the shop and start cleaning the engine compartment, it should look nice. My valve covers are done being power coated. I guess the guy told me they look just beautiful. Hopefully I can pick those up next week. I love trading computer work for car parts

Scorps · 04-15-2004, 07:03 AM

Progress seems to be going along smooth....What colour are you going to paint the car...or are you not right now?

Destrox · 04-17-2004, 03:05 PM

I dont have anything worth while to add to this other then how I completly love reading this!

Keep us updated with text and images please!

Not the best looking stangs, but I still wouldnt pass it up.

big_bubba · 04-17-2004, 10:53 PM

Quote:

Originally posted by merkerguitars
Well said Shakran...every car has it highs and lows

Yeah, you're right. Sorry dude, I was being a prick. Don't try to tell me you can't make a V8 car handle though---just takes a shitload of work.

I guess I'm stuck in that "support your own" frame of mind because of my family and the steel plant, etc. But I won't jack the trhead and go into that.

keep it up Merker, your car is gonna rock!

redarrow · 04-18-2004, 01:17 PM

I gotta give you props dude, that must take some skill.

merkerguitars · 04-18-2004, 09:26 PM

Thanks guys for you postive comments

About painting it, I probably won't paint it till next year I know a guy who runs an awesome body shop and if I do a majority of the prep work i'll save alot of $$$ I'll paint it the factory colors when I repaint it. It's kinda scary but I did an estimate and after I'm done getting it pretty nice shape I'll have over $7k in the car, but damn is it gonna be nice and it will be pretty custom. With gas prices the way they are thank god it's not my primary driver. Breaking it in is gonna be spendy though...lol oh well.....someday we'll tap that rich alaskan soil......

Scorps · 04-19-2004, 08:29 AM

Quote:

Originally posted by merkerguitars
Thanks guys for you postive comments

About painting it, I probably won't paint it till next year I know a guy who runs an awesome body shop and if I do a majority of the prep work i'll save alot of $$$ I'll paint it the factory colors when I repaint it. It's kinda scary but I did an estimate and after I'm done getting it pretty nice shape I'll have over $7k in the car, but damn is it gonna be nice and it will be pretty custom. With gas prices the way they are thank god it's not my primary driver. Breaking it in is gonna be spendy though...lol oh well.....someday we'll tap that rich alaskan soil......

Factory paint.....oh man!

merkerguitars · 04-20-2004, 08:01 PM

w00t more progress.

I just ordered a milodon windage tray. Also i started to sand blast my factory air filter, timing tab, and radiator mounts. Also I'm going to send my intake to get powered coated clear. It's gonna look so purty!

Scorps · 04-21-2004, 07:34 AM

also remember to take really good care of the T-Roof glass, they are hard to find!

jizzmasterp · 04-26-2004, 08:11 PM

I love reading this. I can't wait to see the engine fully painted.

Mondak · 04-27-2004, 10:01 AM

Very interesting thread to be sure! I will have to follow the progress. The interior and exteririer will be a lot of work. Until then your car will be somewhat stealth.

merkerguitars · 04-28-2004, 08:30 AM

Well i'm still waiting for my parts to come...they should be here this week and maybe during the weekend i'll prep for assembly. If anybody has a timing chaing cover they will sell i'll buy it.

Quote:

Originally posted by Mondak
Very interesting thread to be sure! I will have to follow the progress. The interior and exteririer will be a lot of work. Until then your car will be somewhat stealth.

Yeah thats the plan the car looks ok...but no one is gonna believe how powerful it is for how shitty it looks.
Hopefully by the end of this week I will order an alternator, ignition box and ignition coil

TheClarkster · 04-29-2004, 11:53 AM

This is so fun to read! Makes me motivated to go work on my car.... almost.
Keep up the good work and report back with engine pictures!

Scorps · 04-30-2004, 02:34 PM

Quote:

Originally posted by TheClarkster
This is so fun to read! Makes me motivated to go work on my car.... almost.
Keep up the good work and report back with engine pictures!

Engine pics would be sweet..even though this a Ford he is rebuilding....but I love watching projects come together!

merkerguitars · 04-30-2004, 04:48 PM

Well the only parts i got this day are the windage tray installation kit...i'm so hoping my windage tray comes in. I found the easiest way for me to port and flow my heads. At a place I do computer work for they build stuff out of steel (I beams and such for buildings) and i'm gonna take a junk head i got for free and chop it into sections so I can see where the water jackets are.

Scorps · 04-30-2004, 05:01 PM

Quote:

Originally posted by merkerguitars
Well the only parts i got this day are the windage tray installation kit...i'm so hoping my windage tray comes in. I found the easiest way for me to port and flow my heads. At a place I do computer work for they build stuff out of steel (I beams and such for buildings) and i'm gonna take a junk head i got for free and chop it into sections so I can see where the water jackets are.

why would you want to know where the water jackets are?

merkerguitars · 04-30-2004, 05:22 PM

Quote:

Originally posted by Pain Train
why would you want to know where the water jackets are?

so when i grind away at the exhaust and intake runners in the head i don't grind to far and ruin a perfectly good set of heads

Scorps · 05-01-2004, 07:48 AM

Quote:

Originally posted by merkerguitars
so when i grind away at the exhaust and intake runners in the head i don't grind to far and ruin a perfectly good set of heads

oh yes...thats why you get a machine shop to do that!

merkerguitars · 05-04-2004, 08:14 PM

Quote:

Originally posted by Pain Train
oh yes...thats why you get a machine shop to do that!

I don't think i'll pay a machine shop $60 an hour to do that...

well today I got some more parts.....electric fan relay kit, throwout bearing and a brand spanking new power steering pump.

My underdrive pulleys

ElwoodBlues · 05-06-2004, 10:10 PM

I love checking up on your progress every so often. I can't wait to see this car come together

leftturn109 · 05-07-2004, 01:44 AM

sweet keep those pickture comming

merkerguitars · 05-07-2004, 11:53 AM

Well I picked up that old head from my friends place and i gutted the valves out of 2 combustion chambers.....and hopefully next week I'll be able to chop the head apart......i'm going to chop one exhaust runner and one intake runner then port and flow another and then chop those aparts, i'll turn the pieces into a display model for my friend that runs a performance part shop...Tonight I just picked up a universal wiper resevoir (so (I can get rid of the crappy windshield washer/coolant catch tank) I won a fram racing fuel filter assembly...it's used so I had to order replacement filter for it....

merkerguitars · 05-15-2004, 08:00 PM

Got so more gaskets today that I ordered off of ebay.....got my fuel filter...I have to sandblast and repaint the housing and make a bracket for it....got my timing chain cover........

Scorps · 05-16-2004, 09:45 AM

Quote:

Originally posted by merkerguitars
Got so more gaskets today that I ordered off of ebay.....got my fuel filter...I have to sandblast and repaint the housing and make a bracket for it....got my timing chain cover........

your going crazy...you should have that thing running before fall

merkerguitars · 05-17-2004, 09:17 PM

Well today I went to my parents and started to do more work. All I pretty much did was dry fit my timing cover, water pump and AC eliminator. I found out I need a newer style power steering pump bracket, at least I can find one of those easily. Also this week i'm going to move the block from my dad's shop down to my parents garage and start to assemble it there.

merkerguitars · 06-02-2004, 09:29 AM

Well it's seem like my project was on hiatus for a while but I just ordered a bunch more parts!!!!!!

What i ordered

Spark plug wires, nice taylor 8mm wires, the separators for them (dont' want to burn them up on my headers) MSD 6AL box, MSD Blaster SS pump, holley blue electric fuel pump, fuel pressure regulator and got my whole clutch ordered....hopefully i will have some pics up soon!

Scorps · 06-02-2004, 12:08 PM

Quote:

Originally posted by merkerguitars
Well it's seem like my project was on hiatus for a while but I just ordered a bunch more parts!!!!!!

What i ordered

Spark plug wires, nice taylor 8mm wires, the separators for them (dont' want to burn them up on my headers) MSD 6AL box, MSD Blaster SS pump, holley blue electric fuel pump, fuel pressure regulator and got my whole clutch ordered....hopefully i will have some pics up soon!

Damn, must be nice to have your kinda money

TioTaco · 06-08-2004, 02:41 PM

80s mustangs = booboos

merkerguitars · 06-08-2004, 05:23 PM

Quote:

Originally posted by TioTaco
80s mustangs = booboos

wtf???

choskins · 06-08-2004, 05:35 PM

Great looking work to this point!

What is the total dollar output to this point?
Just Curious.

merkerguitars · 06-08-2004, 09:44 PM

Quote:

Originally posted by choskins
Great looking work to this point!

What is the total dollar output to this point?
Just Curious.

Thanks...so far I have about $3k total into the car...that engine and accessories to get it running. Total I figure I will have into it will be about $9k when finished, but the car will be in nice condition with a tough drivetrain, great engine...good looks...and no rust at all....plus it will be totally custom inside and out.....yes I could of blown the money on a different car..but this will be my baby...

Update:
Well I started to clean up my radiator and some of the fins just crumbled into dust...so I need a new radiator.....well I priced out what to get for one...either I can spend the money for a factory one...or spend a little bit more and get a racing aluminum one that will look nice and last longer...I think i'm going to take that route instead of the factory one.

03-28-2004, 09:35 PM	#122 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Underdrive pulleys reduce how much your alternator, water pump and power steering turn so you free up more horsepower....less work they do = more hp __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

03-29-2004, 10:52 AM	#124 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Yup less power from the alternator but I have to buy a bigger alternator cause mine is a 55 amp from the factory and there is no way it will power my electric fan, electric fuel pump, and a small decent stereo system all at once.... This is what I need to buy yet to get it finished Motor mounts and transmission mounts electric fuel pump fuel filter MSD 6al ignition box 2 gauge cable to move my battery to the trunk hi torque starter 105 amp alternator Battery box Thermostat housing Thermostatic switch to turn my electric fan on and off automatically Relays for rewiring my power under the hood Electric Fan Roller Rocker arms New Head bolts Hose Clamps Radiator clmap lower radiator hose water pump to intake manifold hose synthetic atf spark plug wires power steering pump u joint 4 gauge wire fuel pump block off plate cable ties lots of oil 20qts+ oil filter oil pressure sensor clutch steel input bearing retainer for my tranny tranmission seals (might as well replace them why the tranny is out) serpentine belt ignition coil __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

03-31-2004, 06:12 AM	#126 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Ok I just ordered a bunch of stuff, roller rockers, carb studs, arp head bolts, fuel pump blockoff plate, chrome thermostat housing. I picked up my block, wow it's beautiful, some bastard put a 3.8 taurus engine on the stand that my friend loaned me so i'm gonna have to take the engine and chuck it outside. Hopefully this weekend I can get the engine on the stand, then I can start assembling. __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

04-05-2004, 11:27 PM	#127 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Well I got my block on the stand and painted, I'll have to post pics of it. It took me about 1/2 hour to mask everything off but I had very very little overspray. I decided not to assemble till I have all my parts ready so I can assemble it in a day. I started to clean up the wiring in the engine compartment.....not to bad....I have alot of stuff I need to get rid of. Some of the stuff has been cut and spliced before....but shouldn't take me too long to clean up. I just have to double check what some of the wires are before cutting them. Then I can steam blast and paint it __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

04-08-2004, 01:39 PM	#129 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	w00t got some parts today my forged aluminum roller rockers came and my chrome thermostat housing also I bought a set of mechanical gauges Update April 12th I have to call the machine shop today and see if my heads are done. No pics until next week. I loaned my camera to my roomate that will be on vacation for a week. I started snipping wires....and I fucked up big time and lost my lights turns out the ammeter wire is tied in with the head lights...but it's easily fixable. I bought a dealer wiring manual on ebay. All my manuals have shitty wiring diagrams and some of the diagrams are the wrong color codes. Hopefully next week i'll start to make my custom gauge holder. I want to put quick disconnects on the headlight wiring so I can pull the harness back and steam blast all the paint off of all the sheet metal in my engine compartment. I was looking at my rubber fuel lines. One has some nice scarring on it. Thankfully I never drove the car. I'm gonna replace all the rubber lines. __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985 Last edited by merkerguitars; 04-12-2004 at 06:43 AM..

03-30-2004, 08:49 AM	#125 (permalink)
Scorps Lost!! Location: Kingston, Ontario	WOW! that is going to burn I nice hole in your pocket....must be nice to have that kinda money.....I hoping I can afford the get a loan soon!

04-06-2004, 08:19 AM	#128 (permalink)
Scorps Lost!! Location: Kingston, Ontario	Damn this is the fun part....I love putting engines back together!

04-14-2004, 09:26 PM	#130 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Ok now i decided to buy a windage tray. I am pretty much buying one cause my dad highly recommended it. Hopefully after I rack in some more money next week I'll be able to buy my MSD 6AL box and a nice Optima red top battery. And luckily in a few weekends I can assemble my engine. Next week i'm gonna pull my car into the shop and start cleaning the engine compartment, it should look nice. My valve covers are done being power coated. I guess the guy told me they look just beautiful. Hopefully I can pick those up next week. I love trading computer work for car parts __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

04-15-2004, 07:03 AM	#131 (permalink)
Scorps Lost!! Location: Kingston, Ontario	Progress seems to be going along smooth....What colour are you going to paint the car...or are you not right now?

04-17-2004, 03:05 PM	#132 (permalink)
Destrox Metal and Rock 4 Life Location: Phoenix	I dont have anything worth while to add to this other then how I completly love reading this! Keep us updated with text and images please! Not the best looking stangs, but I still wouldnt pass it up. __________________ You bore me.... next.

04-18-2004, 01:17 PM	#134 (permalink)
redarrow Banned Location: i gotta go	I gotta give you props dude, that must take some skill.

04-18-2004, 09:26 PM	#135 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Thanks guys for you postive comments About painting it, I probably won't paint it till next year I know a guy who runs an awesome body shop and if I do a majority of the prep work i'll save alot of $$$ I'll paint it the factory colors when I repaint it. It's kinda scary but I did an estimate and after I'm done getting it pretty nice shape I'll have over $7k in the car, but damn is it gonna be nice and it will be pretty custom. With gas prices the way they are thank god it's not my primary driver. Breaking it in is gonna be spendy though...lol oh well.....someday we'll tap that rich alaskan soil...... __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

04-20-2004, 08:01 PM	#137 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	w00t more progress. I just ordered a milodon windage tray. Also i started to sand blast my factory air filter, timing tab, and radiator mounts. Also I'm going to send my intake to get powered coated clear. It's gonna look so purty! __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

04-21-2004, 07:34 AM	#138 (permalink)
Scorps Lost!! Location: Kingston, Ontario	also remember to take really good care of the T-Roof glass, they are hard to find!

04-26-2004, 08:11 PM	#139 (permalink)
jizzmasterp Insane	I love reading this. I can't wait to see the engine fully painted. __________________ Don't mind the name. It was chosen before I discovered that there were forums that didn't start with "Titty."

04-27-2004, 10:01 AM	#140 (permalink)
Mondak Industrialist Location: Southern California	Very interesting thread to be sure! I will have to follow the progress. The interior and exteririer will be a lot of work. Until then your car will be somewhat stealth. __________________ All truth passes through three stages: First it is ridiculed Second, it is violently opposed and Third, it is accepted as self-evident. ARTHUR SCHOPENHAUER (1788-1860)

04-29-2004, 11:53 AM	#142 (permalink)
TheClarkster Very Proud of Ya Location: Simi Valley, CA	This is so fun to read! Makes me motivated to go work on my car.... almost. Keep up the good work and report back with engine pictures! __________________ Do not speak Latin in front of the books.

04-30-2004, 04:48 PM	#144 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Well the only parts i got this day are the windage tray installation kit...i'm so hoping my windage tray comes in. I found the easiest way for me to port and flow my heads. At a place I do computer work for they build stuff out of steel (I beams and such for buildings) and i'm gonna take a junk head i got for free and chop it into sections so I can see where the water jackets are. __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

05-06-2004, 10:10 PM	#149 (permalink)
ElwoodBlues Psycho Location: Massachusetts	I love checking up on your progress every so often. I can't wait to see this car come together __________________ I think Pringles initial intention was to make tennis balls. But on the day that the rubber was supposed to show up, a big truckload of potatoes arrived. But Pringles is a laid back company. They said "Fuck it. Cut em up." -Mitch Hedberg, '68-'05 Bauer's the man.

05-07-2004, 01:44 AM	#150 (permalink)
leftturn109 Crazy Location: Olalla washington	sweet keep those pickture comming

05-07-2004, 11:53 AM	#151 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Well I picked up that old head from my friends place and i gutted the valves out of 2 combustion chambers.....and hopefully next week I'll be able to chop the head apart......i'm going to chop one exhaust runner and one intake runner then port and flow another and then chop those aparts, i'll turn the pieces into a display model for my friend that runs a performance part shop...Tonight I just picked up a universal wiper resevoir (so (I can get rid of the crappy windshield washer/coolant catch tank) I won a fram racing fuel filter assembly...it's used so I had to order replacement filter for it.... __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985 Last edited by merkerguitars; 05-07-2004 at 04:22 PM..

05-15-2004, 08:00 PM	#152 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Got so more gaskets today that I ordered off of ebay.....got my fuel filter...I have to sandblast and repaint the housing and make a bracket for it....got my timing chain cover........ __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

05-17-2004, 09:17 PM	#154 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Well today I went to my parents and started to do more work. All I pretty much did was dry fit my timing cover, water pump and AC eliminator. I found out I need a newer style power steering pump bracket, at least I can find one of those easily. Also this week i'm going to move the block from my dad's shop down to my parents garage and start to assemble it there. __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

06-02-2004, 09:29 AM	#155 (permalink)
merkerguitars Buffering......... Location: Wisconsin...	Well it's seem like my project was on hiatus for a while but I just ordered a bunch more parts!!!!!! What i ordered Spark plug wires, nice taylor 8mm wires, the separators for them (dont' want to burn them up on my headers) MSD 6AL box, MSD Blaster SS pump, holley blue electric fuel pump, fuel pressure regulator and got my whole clutch ordered....hopefully i will have some pics up soon! __________________ Donate now! Ask me How! Please use the search function it is your friend. Look at my mustang please feel free to comment! http://www.tfproject.org/tfp/showthread.php?t=26985

06-08-2004, 02:41 PM	#157 (permalink)
TioTaco Banned	80s mustangs = booboos

06-08-2004, 05:35 PM	#159 (permalink)
choskins Psycho Location: Greenville, SC	Great looking work to this point! What is the total dollar output to this point? Just Curious. __________________ "Sometimes a cigar is just a cigar." - Sigmund Freud